Start with the equipment and the project
This guide addresses a Non-Running Smardt Chiller in Florida. Selling a machine involves more than stating its cooling capacity: the owner must identify what is included and consider how the buyer can reach it. We buy used and surplus commercial chillers throughout Florida, and all tonnages and refrigerants can be considered. A test run is not required. Even when a nameplate or service history is unavailable, an owner or authorized representative can begin a conversation by describing the equipment, its known condition and its location. The commercial agreement and the physical removal plan should be considered together.
No test run is required
The equipment does not need to be started or tested for us to consider it. That can matter when a chiller is idle, disconnected, missing a component or no longer part of the active cooling plan. Describe the known condition honestly and distinguish what you have observed from information you do not have. A photograph or old service note may be useful, but neither is a prerequisite for making contact. Do not reconnect equipment or attempt a test simply to request an offer. The buyer can review available information and discuss any uncertainties as part of the proposed sale.
Identify the actual machine, not just the brand
The manufacturer name is a useful starting point, but it does not by itself identify a chiller's model, capacity, refrigerant, weight or present condition. If an accessible nameplate or equipment record is available, share its details along with a safe photograph of the full unit. If the model cannot be read, describe the machine and its surroundings instead; the absence of a label does not prevent an initial discussion. We are a buyer of used equipment, not a claim of manufacturer authorization or affiliation. The offer and removal approach depend on the actual unit and agreed scope.
Refrigerant identification and recovery
All refrigerants can be considered; an owner does not need to identify the refrigerant before making contact. If information is available on a nameplate or in existing records, share it and specify which machine it refers to. Do not assume the original label necessarily describes the present contents. Refrigerant recovery is work for appropriately qualified professionals using a plan suited to the equipment and applicable requirements. We handle recovery as part of the agreed removal scope. Owners should not vent, release or attempt to recover refrigerant themselves merely to prepare a chiller for sale.
Plan the handoff to freight
The final loading point matters even when freight is covered. A removal team needs to understand whether the unit can be staged near a truck, whether the access route has restrictions and who will coordinate entry to the property. A rooftop or indoor machine may need additional handling before it reaches that point. Describe what you know and flag anything that still needs review. We handle the loading, freight and hauling included in the agreed purchase; the site-specific method depends on the machine and property. Confirm any required handoff with the facility contact before the scheduled work.
An idle machine can still be considered
Equipment may have been shut down because a facility changed its cooling arrangement, a replacement project began or the machine was no longer needed. Do not assume the reason for shutdown if it is not known. Share whether the unit appears intact, whether it remains connected and how long it has been idle if that information is available. A machine can be considered without being restarted or tested. These distinctions help the buyer understand the project, while the offer and the removal method remain subject to the actual equipment and an agreement with its owner.
Measure the route as well as the machine
A chiller that fits in its present location may still be difficult to move through the route available for removal. Useful information includes the approximate length, width and height of the equipment, the size of nearby openings and any turns or obstacles between the machine and an appropriate loading area. Record uncertainty instead of presenting an estimate as an exact measurement. A photograph showing the machine in relation to doors, pipes or adjacent equipment can make the discussion more productive. The actual plan depends on the site and should be confirmed by the people responsible for rigging and removal.
What to share when you contact us
If the chiller may be available, contact us with a description and the location in Florida. Existing labels, photos and records can help, but they are not prerequisites and the unit does not need to be tested. Explain whether anything must remain connected or operating around it and who has authority to approve the sale. We can discuss the cash offer, upfront payment and the appropriate recovery, disconnect, rigging and freight arrangements. The owner can decide whether the agreed scope suits the project.
- Identify the equipment and the person authorized to sell it.
- Share safe photographs or existing records if available; neither testing nor complete records are required.
- Discuss access, included work, payment and timing before scheduling removal.