Start with the equipment and the project
For anyone researching a surplus screw chiller in Fort Myers, Florida, the practical starting point is the equipment owner and the unit that owner wishes to sell. A model number can help, but missing records do not need to prevent an initial inquiry. We buy used and surplus chillers across Florida and consider all tonnages and refrigerants; no testing is required. The buyer also needs to understand the likely access route, any known connections and which equipment remains outside the sale. Those details support an agreed scope rather than a guess about the project.
What to share about a screw chiller
A screw chiller should be identified by its available nameplate and overall configuration rather than by compressor type alone. Tell the buyer where the unit sits, whether it remains connected and whether there are known missing components. If information is uncertain, do not invent a model number or refrigerant. Some machines are accessible from an outdoor area while others have different site constraints; the actual property determines the handling plan. We can consider a unit without a test run. The agreed project can include qualified recovery and disconnect work, rigging, loading and covered freight.
Service planning starts with the actual property
The city or county tells us where a project is being considered, but it does not reveal where a particular machine is located within a property or how it can be removed. Tell us whether the unit is indoors, outside or on a roof, and share any access limits known to the facility team. Avoid assuming that a nearby buyer must have a local office or that every site has the same loading arrangements. We buy used chillers throughout Florida and coordinate the agreed work. The practical plan depends on the equipment, ownership, access and site schedule.
No test run is required
The equipment does not need to be started or tested for us to consider it. That can matter when a chiller is idle, disconnected, missing a component or no longer part of the active cooling plan. Describe the known condition honestly and distinguish what you have observed from information you do not have. A photograph or old service note may be useful, but neither is a prerequisite for making contact. Do not reconnect equipment or attempt a test simply to request an offer. The buyer can review available information and discuss any uncertainties as part of the proposed sale.
Refrigerant identification and recovery
All refrigerants can be considered; an owner does not need to identify the refrigerant before making contact. If information is available on a nameplate or in existing records, share it and specify which machine it refers to. Do not assume the original label necessarily describes the present contents. Refrigerant recovery is work for appropriately qualified professionals using a plan suited to the equipment and applicable requirements. We handle recovery as part of the agreed removal scope. Owners should not vent, release or attempt to recover refrigerant themselves merely to prepare a chiller for sale.
Separate electrical and mechanical disconnect planning
A chiller may have electrical, control, refrigerant and fluid connections, each of which should be considered in the removal scope. The fact that a machine is not running does not establish that every connection is isolated. Tell the buyer whether the equipment remains connected and identify the facility contact who understands the surrounding system. We handle necessary disconnects as agreed, using appropriately qualified personnel. The owner should not cut, open or energize connections for the purpose of requesting an offer. The people responsible for the site can coordinate the work so equipment outside the sale is clearly distinguished.
Identify equipment and connections that must remain
A chiller can sit beside pumps, controls, piping and other machinery that are not part of the sale. Some connections may serve more than one piece of equipment, so a visual boundary around the machine is not always the whole project boundary. Identify the intended unit and let the facility's knowledgeable contact explain what must stay in service. Do not label a shared component as surplus merely because it is nearby. The buyer and owner should agree whether any auxiliary items are included and how the necessary disconnects will be coordinated before work starts.
What to share when you contact us
If the chiller may be available, contact us with a description and the location in Florida. Existing labels, photos and records can help, but they are not prerequisites and the unit does not need to be tested. Explain whether anything must remain connected or operating around it and who has authority to approve the sale. We can discuss the cash offer, upfront payment and the appropriate recovery, disconnect, rigging and freight arrangements. The owner can decide whether the agreed scope suits the project.
- Identify the equipment and the person authorized to sell it.
- Share safe photographs or existing records if available; neither testing nor complete records are required.
- Discuss access, included work, payment and timing before scheduling removal.